Ez az oldal az Ön nyelvén jelenleg nem elérhető. Az automatikus fordítás a megtekinthető a Google Fordító segítségével. A szolgáltatás biztosításáért nem vállalunk felelősséget, a fordított szöveget nem ellenőrizzük.
Ha további segítségre van szüksége, lépjen kapcsolatba velünk.

BiSS® protocol support

What is the BiSS serial interface?

Renishaw supports BiSS (unidirectional) open serial interface for absolute encoders. BiSS is a high-speed serial interface, perfect for dynamic axes that require high acceleration, smooth velocity control, excellent bi-directional repeatability and dependable positional stability.

Renishaw absolute encoders are compatible with a wide range of industry-standard controllers, drives, DROs and PC counter cards.

Proprietary serial interface options for RESOLUTE™, EVOLUTE™ and FORTiS™ absolute encoders are also available.

Technical information

About RESOLUTE, EVOLUTE and FORTiS encoders

Renishaw RESOLUTE, EVOLUTE and FORTiS encoders use the BiSS C (unidirectional) serial interface.

RESOLUTE FS and FORTiS FS encoders, for applications requiring Functional Safety, use the BiSS Safety serial interface.

  • Rotary encoders are single-turn (with 2n counts per revolution and no revolution counting).
  • Linear encoders are available with a range of different resolutions (and maximum measuring lengths) as specified on the product data sheet.


Description of the BiSS C interface

BiSS C-mode (unidirectional) is a fast synchronous serial interface for acquiring position data from an encoder.
It is a master-slave interface. The master controls the timing of position acquisition and the data transmission speed,
and the encoder is the slave. The interface consists of two unidirectional differential pairs of lines:

  • “MA” transmits position acquisition requests and timing information (clock) from master to encoder
  • “SLO” transfers position data from encoder to master, synchronised to MA.

The diagram below shows the data transmitted.

Data format

BiSS data transmission



Description of the BiSS Safety interface

BiSS Safety is a fast synchronous serial interface for acquiring position data from an encoder in applications requiring Functional Safety. RESOLUTE FS and FORTiS FS use BiSS Safety communications and are certified to the following Functional Safety standards:

  • ISO 13849 Category 3 PLd
  • IEC 61508 SIL2
  • IEC 61800-5-2 SIL2

BiSS Safety is a master-slave interface. The master controls the timing of position acquisition and the data transmission speed, and the encoder is the slave. The interface consists of two unidirectional differential pairs of lines:

  • “MA” transmits position acquisition requests and timing information (clock) from master to encoder.
  • “SLO” transfers position data from encoder to master, synchronised to MA.

The diagram below shows the data transmitted.

The master-slave signal communication format is RS485 / RS422 differential line-driven.

Data format

BiSS Safety data transmission


A typical request cycle proceeds as follows:

  1. When idle, the master holds MA high. The encoder indicates it is ready by holding SLO high.
  2. The master requests position acquisition by starting to transmit clock pulses on MA.
  3. The encoder responds by setting SLO low on the second rising edge on MA.
  4. After the “Ack” period is complete, the encoder transmits data to the master synchronised with the clock as shown in the diagrams above.
  5. When all data has been transferred, the master stops the clock and sets MA high.
  6. If the encoder is not yet ready for the next request cycle, it sets SLO low (the Timeout period).
  7. When the encoder is ready for the next request cycle, it indicates this to the master by setting SLO high.

RESOLUTE open absolute encoders with BiSS C and BiSS Safety

RESOLUTE variantsSystem options
Standard

Linear scales

Partial arc scales

Rotary (angle) rings

Ultra-high vacuum (UHV)

Linear scales

Rotary (angle) rings

Extended Temperature Range (ETR)Rotary (angle) rings
Functional Safety (FS)

Linear scales

Rotary (angle) rings

EVOLUTE open absolute encoders with BiSS C

EVOLUTE variantsSystem options
Standard

Linear scales

FORTiS enclosed absolute encoders with BiSS C and BiSS Safety

FORTiS variantsLinear system options
Standard

FORTiS-S

FORTiS-N

Functional Safety (FS)

FORTiS-S FS

FORTiS-N FS

Downloads